CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma
Connecting the Battery CablesCALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, che
Adjusting the Seat To adjust the position of the seat, pull up and hold the seat adjustment lever. Slide the seat forward or rearward to the desired p
Systems Indicator MonitorBrake PedalDrive PedalDeck Lift LeverCup HolderFuel Tank CapThrottle/Choke ControlIgnition Switch ModuleParking Brake/Cruise
Deck Lift Leverchange the height of the cutting deck. To use, move the lever to t
Fuel Level IndicatorThe Fuel Level Indicator is located on the left side of the tank.PTO /
Safety Interlock SwitchesThis tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ev
Driving The TractorWARNING! Avoid sudden starts, excessive speed and sudden stops. Lightly press the brake pedal to release the parking brake. Mov
Driving On Slopeswhere you may operate the tractor safely.WARNING! Do not mow on inclines
2. NOTE: Always operate the tractor with the throttle lever in the
Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursEvery 50 HoursEvery 100 HoursPrior to StoringClean Hood/Dash LouversP PCheck Engine Oi
Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine
Remove the oil fill cap/ dipstick from the oil
Attach the hose coupler to the water port on your decks 4. surface. See Fig. 6-2.Turn the water on.5.
Deck SpindleGrease fittings can be found on each deck spindle. See Fig. 6-4. purpose lithiu
Leveling the Deck (Side to Side)If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as
Cutting Deck RemovalTo remove the cutting deck, proceed as follows:position and engage the
5. 6. Mo
To properly sharpen the cutting blades, remove equal 4. amounts of metal from both ends of the blades along the
FuseWARNING! Before servicing, repairing, or brake, stop engine and remove key to prevent unintended sta
To place the new belt begin by routing the belt around the 5. two outer spindle pulleys, then around the front spindle pulley as shown in Fig. 7-8.The
Problem Cause RemedyEngine fails to start 2. Spark plug wire(s) disconnected. Throttle
Important Safe Operation Practices23General OperationRead, understand, and follow all instructions on the machine and in the manual(s) before attem
Component Part Number and Description
which you purchased you
Notes1133
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe California Air Resources Board and MTD Consumer Group Inc are pl
WARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage i
IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Pl
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade contact or th
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sChildrenTragic accidents can occur if the operator is not alert to the
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e scomplete stop wi
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may a
8 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSight and hold this level with a vertical tree...or a corner of a buil
Tractor Set-UpMoving The Tractor Manuallyrelief valve for occasions when it is necessary to
Kommentare zu diesen Handbüchern