Commercial Zero-Turn Riding MowerProfessional Turf EquipmentOPERATOR’S AND SERVICE MANUAL S6031 S7231 S7237
10OPERATING INSTRUCTIONSFigure. 4 Figure. 5Ignition SwitchElectric BladeClutch SwitchTach andHour MeterEngine throttleChoke LeverPower Implement LiftA
11grounds, parking lots, other machines, ani-mals, and other people.e. Avoid operation or use extreme care if the traction surface is wet, unstable, o
12one hand is required to reposition the pins to pro-vide 1/4” height-of-cut increments. The mechanism includes: A hydraulic cylinder that is used to
134.Adjust the Mowing Deck: The cutting height is set anywhere in the range of 1" to 5". You may need to adjust the mowing deck to achieve t
141. All guards, shields (including mower chute deflector) are in their proper place, are secure, and are functional.2. That there are no spilled or l
15well as potential damages to the traction surface and the tire. If the inside wheel is not turned 88 degrees, then the turn side tire will continue
16(I.E., the blades do not need to be “timed” nor synchro-nized).Hi-lift- These are generally the best cutting blades for most grasses and mowing cond
172.Figure. 10CoverPlateSpindleChanging a Blade:a. Remove the Key from the ignition and dis-connect the spark plug.b. Jack up the front of the mowing
181.Hydraulic TankFigure. 11Adding Hydraulic Oil (use Rimula SAE15W40)a. Place the Mower on a level surface and engage the parking brake.b. Stop the e
19c. Store the battery with a full charge. A dis-charged battery will freeze (refer to the table below).Specific Gravity Freezing Temp (°F)1.265 -711.
2TABLE OF CONTENTSForeword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20b. Parking Brake Switch: Sit in the operator’s seat. With the speed control pedals in the neutral position and the blade clutch switch “off”, releas
213.Creeping: Creeping is the slight forward or backward movement of the mower when the throttle is on and the speed control pedal is in the neutral p
22neck. Leave this air space for expansion. Start the engine and let it run at low idle for about five minutes. Check the filter for leaks. Idling the
23fuel line on the carburetor. Start the engine and allow it to run out of fuel. This will pre-vent gum and varnish deposits from form-ing. Replace th
24MAINTENANCE SCHEDULEA. Daily Checks1. Before starting engine:a. Check the fuel level.**b. Check the engine oil level.**c. Check the hydraulic oil le
25.OIL CHARTApply a few drops of engine oil or use a spray lubricant. Apply the oil to both sides of pivot points. Wipe off any excess. Start engine a
26Performance AdjustmentsA. Engine RPM Check and AdjustmentDescription High RPM Spec. Low RPM Spec.31 & 37 Kawasaki 3600 +/-50 1550 +/-100NOTE: RP
27key from the ignition switch, disconnect the spark plug wires and lower the mowing deck into the 4" height of cut position. (The 4" height
28WIRING DIAGRAMGD: 02002824
29FrontSkirtInnerBaffleDischargeBaffleCuttingBlades Gauge Wheels Front Roller Rear RollersStandard set-upLow installed installed Hi-lift Low = 3"
3FOREWORDThe Tank Hydrostatic Zero-Turn Synchro-Steer Commercial Riding Mower provides superb maneuverability, mid-mount cutting capability for profes
30SLOPE GAUGEDo not mow on inclines with a slope in excess of 20 degrees (a rise of approximately 3 feet every 10 feet). A riding mower could overtur
31This page intentionally left blank.
32This page intentionally left blank.
33This page intentionally left blank.
34CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe California Air Resources Board and MTD Consumer Group Inc are
35WARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage
Cub Cadet LLC - P.O. Box 361131, Cleveland, Ohio 44136-0019; Phone 1-877-282-8684MANUFACTURER’S LIMITED WARRANTY FOR CUB CADET COMMERCIAL TANK ZERO-TU
4GENERAL SAFETYOPERATIONSA. DANGER1. Do not operate machine in confined areas where exhaust gases can accumulate.2. Do not operate machine without mow
5removed within a few hours by a doctor familiar with this form of injury or serious complications may result.B. Related to Fuel1. Fuel is highly flam
6blade clutch switch if another person approaches while you are operating the mower.15. Never attempt to operate the traction unit with-out the mowing
7file mechanical suspension, and an Operator Presence Sensor (OPS).2. The seat bottom is covered with a heavy-duty vinyl fabric. An OPS in the form of
WARNINGSHIELD MISSINGDO NOT OPERATEPart Number: 00030635Part Number: 777S30503Part Number: 01002166Part Number: 777S33087 Part Number: 02005110Part Nu
9SPECIFICATIONSGENERAL INFO.Controls: Engine ignition and start switch; throttle; choke; speed control pedals; electric blade clutch switch; parking b
Kommentare zu diesen Handbüchern