Hydrostatic Zero-TurnResidential Riding MowerTurf EquipmentOPERATOR’S AND SERVICE MANUALMODEL18.5HP Z-Force 4220HP Z-Force 4422HP Z-Force 48
10c. Avoid turning when going downhill, traction is at a minimum going downhill.d. Do not operate with discharge side of the mower toward streets, bui
114.Electric Blade Clutch Switch: (See Figure 1.) Located on the right side of the mower beside the ignition switch. This is an “on/off” push-pull swi
12C. Initial Adjustments1. Check the fluid levels and tires:Note: These checks should be made daily, before starting the engine.a.Fuel: Using a good g
13step “b.” above to make sure that the desired cutting height and pitch and level have been attained. If the dimensions are not correct, repeat steps
14right control panel). This must be increased to full speed (3525-3675 rpm) after becoming familiar with the machine.2. Release the park brake.3. Mov
15g. Turn the ignition key in a clockwise direc-tion to the “Start” position until the engine starts.Note: Do not hold the key in the “Start” position
16e. Remove two linchpins (See Fig. 6) from the front of the mower. Pull the two (2) spring-loaded “J” pins on the left and right rear side of the cut
17Note: When replacing belts do not over-tighten. Adjust the idler pulley so that a ten-pound pull with a spring scale between two pulleys deflects th
18c. Store the battery with a full charge. A dis-charged battery will freeze (refer to the table below).d. Recharge battery when ever the specific gra
19ing brake switch must be repositioned or perhaps replaced. If the engine does not start, engage the parking brake and start the engine. Swing one st
2TABLE OF CONTENTSForeword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20level, paved area. If the leaking tire is on a traction wheel, put blocks on each side of the opposite traction wheel and jack up the tire that leak
21Because of extremely close tolerances, wear is an important factor in their life.Note: The pumps and motors are not owner-repairable. If a pump fail
22c. lubricate the wear points. Follow the Lubri-cation Chart.d. After the first five hours, change the engine oil and engine oil filter.B. Every 25 H
23Performance AdjustmentsA. High Speed Tracking AdjustmentIf mower tracks to one side with both lap bars in fully forward position:1. Check air pressu
24C. Deck Corner Ball Wheel Roller Settings1. Matching the set heights of the ball rollers on the four corners of the mower deck to the desired cut he
25sure, align blades in parallel with mower center-line, (i.e. front to back).5. Measure blade-to-ground height at the front tip of the left blade. Be
26WIRING DIAGRAMGD: 01008375
27SLOPE GAUGEDo not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mowercould over
MANUFACTURER’S LIMITED WARRANTY FOR:TWO-YEAR RESIDENTIALONE-YEAR COMMERCIALProper maintenance of your Cub Cadet equipment is the owner’s responsibilit
3FORWARDThe Hydrostatic Zero-Turn Riding Mower provides superb maneuverability and mid-mount cut-ting. The machine incorporates many safety features
4WARNING• The engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicalsknown to the State of California to ca
514. Do not operate the machine while under the influence of alcohol or drugs.15. Watch for traffic when operating near or crossing roadways.16. Use e
6close parental supervision and proper instruc-tion.6. Use extra care when approaching blind cor-ners, shrubs, trees or other objects that may obscure
7SAFETY DECALS AND LABELS To unlock, pull part of handle inward. Lift unlocked handle to increase cutting height. To lock, release upper part of handl
8SPECIFICATIONSEngine: 18.5HP, 20HP & 22HP Briggs & StrattonType: Vertical air cooled V-TwinAir Cleaner: Paper elementLube System: Pressurize
9OPERATING INSTRUCTIONSA. General1. When Mowing:a. Keep adults, children, and pets away from the area to be mowed.b. When operating this mower, in the
Kommentare zu diesen Handbüchern