Cub Cadet CC 30 Betreibershandbuch

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •

Assembly & Set-Up310Figure 3-14. Lower the steering wheel assembly onto the lower steering shaft and secure with the shoulder bolt and lock nut p

11Section 3 — ASSembly & Set-UpFigure 3-53. Align the seat bracket in place over the holes from where the self-tapping bolts were removed, as sho

12 Section 3— ASSembly & Set-Up12Figure 3-8Installing the Mulch PlugWARNING! NEVER operate this tractor without either the mulch plug or deck chut

13Section 3 — ASSembly & Set-UpInstall The Rear Engine Cover1. Remove the two factory installed hex screws located on the rear engine cover. Ret

14 Section 3— ASSembly & Set-Up2. Remove the plastic cover, if present, from the positive battery terminal and attach the red cable to the positi

Controls & Features415Clutch/Brake PedalSpeed Control & Parking Brake LeverShift LeverCup HolderThrottle/Choke LeverIgnition Switch ModuleDeck

Throttle / Choke ControlThe throttle control lever is located on the left fender of the tractor seated in the operator’s position, see Figure 4-1. Thi

Shift Lever The shift lever is located on the control panel just below the seat, in the center of the tractor. It has three positions, FORWARD, NEUTRA

Operation518WARNINGAvoid Serious Injury or Death• Knowlocationandfunctionofallcontrols.• Removeobjectswhichcouldbethrownbytheblades.•

19Section 5 — operationStopping the EngineWARNING! If you strike a foreign object, stop the engine, disconnect the spark plug wire and ground against

Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.If you have diffic

20 Section 5— operation4. Once activated (indicator light ON), the tractor can be driven in reverse with the cutting blade (PTO) engaged.5. Always l

21Section 5 — operationMulchingA mulch kit has been supplied with your unit. Mulching is a process of recirculating grass clippings repeatedly beneath

MaintenanceWARNING: Before performing any maintenance or repairs, disengage PTO, move shift lever into neutral position, set parking brake, stop engin

BatteryThe battery is sealed and is maintenance-free. Acid levels cannot be checked.• Always keep the battery cables and terminals clean and free of

4. Attach the hose coupler to the water port on your decks surface. See Figure 6-3.Figure 6-35. Turn the water on.6. While sitting in the operator’

TiresWARNING! Never exceed the maximum inflation pressure shown on the sidewall of the tire.The recommended operating tire pressure is:• Approximatel

Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursEvery 50 HoursEvery 100 HoursPrior to StoringCheck Engine Oil LevelP PCheck Air Filter

Se rvi ce7275. Remove the remaining bow-tie cotter pins securing the deck to the unit, as shown in Figure 7-3.Figure 7-3NOTE: The bow-tie clips shoul

28 Section 7— ServiceChanging the Deck BeltNOTE: It is possible to change the deck belt with the cutting deck still installed on the tractor, however

29Section 7 — ServiceJump StartingWARNING! Never jump start a damaged or frozen battery. Be certain the vehicles do not touch, and ignitions are off.

Important Safe Operation Practices23General Operation1. Read, understand, and follow all instructions on the machine and in the manual(s) before atte

30 Section 7— Service4. To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, p

Problem Cause RemedyEngine fails to start 1. PTO/Blade engaged 2. Spark plug wire disconnected3. Fuel tank empty, or stale fuel 4. Choke not acti

Component Part Number and Description954-05001 Drive Belt (Mowing Deck) 918-04822A Deck Spindle942-04385 Cutting Blade (30”)925-1707D Battery

The following attachments and accessories are compatible for Cub Cadet CC-30 riding lawn mower. See your Cub Cadet dealer for information regarding pr

FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS MTD Consumer Group Inc, the United States Environme

063015 Rev. AWARRANTED PARTS: The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warra

IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Pl

4 Section 2 — important Safe operation practiceS12. A missing or damaged discharge cover can cause blade contact or thrown object injuries. 13. Stop

5Section 2 — important Safe operation practiceSChildren1. Tragic accidents can occur if the operator is not alert to the presence of children. Childr

6 Section 2 — important Safe operation practiceS3. Periodically check to make sure the blades come to complete stop within approximately (5) five sec

7Section 2 — important Safe operation practiceSSafety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, un

8 Section 2 — important Safe operation practiceSSymbol DescriptionWARNING—GASOLINE IS FLAMMABLE Allow the engine to cool at least two minutes before r

9Section 2 — important Safe operation practiceS(OK) (TOO STEEP)USE THIS SLOPE GAUGE TO DETERMINEIF A SLOPE IS TOO STEEP FOR SAFE OPERATION!To check th