Cub Cadet 826 SWE Betreibershandbuch

Snow ThrowerModels 826 SWE &1130 SWEPRINTED IN U.S.A.FORM NO. 770-10026C.fm(11/01)OPERATOR’S MANUALIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS C

10WARNING: The temperature of the mufflerand the surrounding areas may exceed150°F. Avoid these areas.• For the most efficient snow removal, remove sn

11• Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding the shift rod connector back down

12There is a grease fitting on the top of the axle shaft which drives the rear track drive wheels on both sides of the unit. Grease these fittings eve

13Figure 13Drive Belt• Follow the first four steps of the instructions for servicing the auger belts.• Pull the idler pulley up and lift the belt off

14Figure 16• Remove the six screws from the friction wheel assembly (three from each side). Remove the friction wheel rubber from between the friction

15SECTION 8: TROUBLE SHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in ON posi

16Notes

1721246710914118161315Models 826 SWE & 1130 SWE513317Ref. No.Part No. Part Description1. 618-0123 RH Housing (Incl. Ref. 17, 18)2. 618-0418 LH Hou

18Models 826 SWE & 1130 SWE14102141216320586661606367655758555481711222118411115195271423383535399432625314041950243731459514046475359296869692782

19Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0262 Carriage Bolt 5/16-18 x 1.5”3. 710-0449 Car

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn

20Models 826 SWE & 1130 SWE12345678910111214151316102122232523222618272813303132331618353436373839414042174039292420919

21Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632A Auger Idler Arm4. 7

22Models 826 SWE & 1130 SWE1234567489101112131415161718191916161620212223242526272829303132333435IMPORTANT: For a proper working machine, use Fact

23Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x .6252. 731-1324 Belt Cover3. 732-0710 Extension

24Models 826 SWE & 1130 SWE72715284429238111136471150521133337333710913134263130169431734463418196391824403432142032353845403432383220149485749364

25Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 618-0043 Dogg Assembly: RH2. 618-0044 Dogg Assembly: LH3. 618-0575 Shift Assembly:

26

27

MANUFACTURER’S LIMITED WARRANTY FOR:TWO-YEAR RESIDENTIALONE-YEAR COMMERCIALProper maintenance of your Cub Cadet equipment is the owner’s responsibilit

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th

43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with

5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’

6Final AdjustmentsAuger Control AdjustmentCheck the adjustment of the auger control as follows:• Push forward on the auger control until the small rub

7• Recheck the adjustment and repeat adjustment as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached.NOTE: If

8Electric Chute-Rotation SwitchThe electric chute-rotation switch is located on the leftside of the snow thrower dash panel. See Figure 7.To change th

9WARNING: The electric starter isequipped with a grounded three-wirepower cord and plug and is designed tooperate on 120 volt AC householdcurrent. It