SNOW THROWERMODEL826 4x44-Wheel DriveOPERATOR’S MANUALPRINTED IN U.S.A.FORM NO. 770-10260A.fm(6/00)IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREF
10• Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unatten
11Figure 9Shift Rod AdjustmentTo adjust the shift rod, proceed as follows:• Remove the hairpin clip and slide the shift rod connector up, to separate
12Electric Chute-Rotation MotorThe gear on the electric chute-rotation motor and the base of the discharge chute itself should be lubed with multi-pur
13 Figure 13• Remove the three hex nuts and lock washers which attach the auger housing assembly to the frame assembly on each side. See Figure 14. WA
14• Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.• Tip the snow thrower up and forward, so that it
15• Reassemble new friction wheel rubber to the friction wheel assembly, tightening the six screws in rotation and with equal force.• Insert the pin f
16SECTION 8: TROUBLE SHOOTING GUIDENOTE: For repairs beyond the minor adjustments listed above, please contact your local Cub Cadet dealer.Trouble Po
17Model 82622212019117141486813613471581416126981416223102318Ref. No.Part No. Description1. 710-0459A Special Hex Screw: 3/8-24 x 1.5”2. 710-0599 TT S
18Model 82642524647504954514856414355455343334457282993052520171413181811327183391023167102322622638593660191246222221322353415212811212640832313322
19Ref. No.Part No. Description1. 05931A Bearing Housing 2. 684-0065 Impeller Assy. 12” dia.3. 705-5226 Chute Reinforcement4. 710-0451 Carriage Bolt 5/
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices... 3Assembling Your S
20Model 8265657594443421348375013544837711499152739252321831244528172910644134347202382514233934411115532185162330111251134837531313383316402216333946
21Model 82637. 738-0924 Shoulder Screw38. 741-0598 Hex Flange Bearing39. 741-0600 Ball Bearing40. 741-0701 Flange Bushing41. 741-1111 Hex Flange Beari
22Model 8261134811832620251422296121623212321231315524197102728293031
23Model 826Ref. No.Part No. Description1. 05896A Idler Bracket2. 710-0230 Hex Bolt 1/4-28 x 0.5” Gr.53. 710-0627 Hex Scr w/ Patch: 5/16-24 x 0.75” 4.
24Model 8261410214121632058666160636765575855548171122211841111519527144942273644302832444810233835353994326253140419502437314595140464753592968696927
25Model 826Ref. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0262 Carriage Bolt 5/16-18 x 1.5”3. 710-0449 Carriage Bolt 5/16-18 x
26Notes
27
MANUFACTURER’S LIMITED WARRANTY FOR:TWO-YEAR RESIDENTIALONE-YEAR COMMERCIALProper maintenance of your Cub Cadet equipment is the owner’s responsibilit
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th
43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with
5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’
6Figure 5Final AdjustmentsAuger Control AdjustmentCheck the adjustment of the auger control as follows:• Push forward on the auger control until the s
7Figure 7• Retighten the hex nuts loosened earlier.• Repeat this adjustment on the skid shoe found on the opposite side of the snow thrower.Tire Press
8Auger Drive ControlThe auger drive control is located on the left handle. Squeeze the control grip to engage the augers. Release to stop the snow thr
9WARNING: Use extreme care whenhandling gasoline. Gasoline is extremelyflammable and the vapors are explosive.Never fuel machine indoors or while thee
Kommentare zu diesen Handbüchern