Cub Cadet 3x28 Betreibershandbuch

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •

10 Section 3— ASSembly & Set-UpOverhead Chute Control AssemblyHandle Assembly1. Loosen the top two lock nuts securing the upper and lower handle

11Section 3 — ASSembly & Set-UpNOTE: Make certain the cables are seated properly in the roller guides. See Figure 3-13.Figure 3-135. Reattach the

12 Section 3— ASSembly & Set-Up4. Remove the hairpin clip from the rear of the chute control assembly.5. Insert flex shaft removed earlier from

13Section 3 — ASSembly & Set-UpChute Clean-Out ToolThe chute clean-out tool is fastened to the top of the auger housing with a mounting clip and a

14 Section 3— ASSembly & Set-UpTo adjust the skid shoes: 1. Loosen the four hex nuts (two on each side) and carriage bolts. Move skid shoes to de

Controls and Features415Snow thrower controls and features are described below and illustrated in Figure 4-1. Shift LeverThe shift lever is located in

16 Section 4 — controlS and FeatureSAuger ControlThe auger control is located on the left handle. Squeeze the control grip against the handle to engag

17Section 4 — controlS and FeatureS4-Way Chute Directional Control (If so Equipped)The chute directional control is located on the left side of the da

Operation518Starting and Stopping the EngineRefer to the Engine Operator’s Manual packed with your snow thrower for instructions on starting and stopp

Maintenance & Adjustments619MaintenanceEngineRefer to the Engine Operator’s Manual.Tire PressureRefer to Assembly and Set-up section for informati

Thank you for purchasing a Cub Cadet Snow Thrower. It was carefully engineered to provide excellent performance when properly operated and maintained

20 Section 6 — Maintenance & adjuStMentSLubricationWheelsAt least once a season, remove both wheels. Clean and coat the axles with a multipurpose

21Section 6 — Maintenance & adjuStMentSFigure 6-73. Pivot the shift bracket downward as far as it will go. See Figure 6-8.Figure 6-84. Rotate t

22 Section 6 — Maintenance & adjuStMentSFigure 6-103. Position the bracket upward to provide more slack (or downward to increase cable tension).

Se rvi ce723Belt ReplacementAuger BeltTo remove and replace your snow thrower’s auger belt, proceed as follows:1. Allow the engine to run until it is

24 Section 7— Service7. Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. See Figure

Troubleshooting825Problem Cause RemedyEngine fails to start 1. Choke not in CHOKE position.2. Spark plug wire disconnected.3. Fuel tank empty or st

Replacement Parts926Component Part Number and Description954-04195A Auger Drive Belt954-04201A Wheel Drive Belt684-04153C Friction Wheel Assembly93

Attachments & Accessories1027The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

Important Safe Operation Practices23Training1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to

4 Section 2 — important Safe operation practiceSSafe Handling of GasolineTo avoid personal injury or property damage use extreme care in handling gaso

5Section 2 — important Safe operation practiceSClearing a Clogged Discharge ChuteHand contact with the rotating impeller inside the discharge chute is

6 Section 2 — important Safe operation practiceSSafety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, u

Assembly & Set-Up37Contents of Carton• Snow Thrower • Replacement Auger Shear Pins • Chute Assembly• Chute Control Rod or Flex Shaft • Engine

8 Section 3— ASSembly & Set-Up4. Secure the handle by tightening the plastic knob located on both the left and right sides of the handle. Remove

9Section 3 — ASSembly & Set-Up5. Rotate the joystick to the one o’clock position so that the silver indicator arrow on the pinion gear below the